|
150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum |
|
Thread Tools |
#1
|
||||
|
||||
Felt something scary today while driving
So, I was out driving today, enjoyin' the new mods, when I'm on a trail and I want to back up to get a lot of speed. When I shifted into reverse, it felt like the reverse gear slipped, as in, one of the teeth on the gear is broken. It would go in reverse, but then it would slip, then catch again. I haven't put it in reverse since because I'm afraid I'll break something. What's happening?
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#2
|
||||
|
||||
uhmm well my carter has done that since the day i bought it. it doesnt seem to do much harm. i would just keep on keepin on! thers not much u can do till its broke. but if its anything like my problem, nothing significant will come of it.
|
#3
|
||||
|
||||
but it didnt do it when i first got it
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#4
|
||||
|
||||
Did you check the reverse cable. It may need to be adjusted if you bought your buggy new I would bet that the cable stretched and when your putting it in reverse its not going all the way in gear. You may need to take up a little of the slack
__________________
Baja Reaction 150 Dr Pulley kit 13g sliders 1500 main spring hammerhead performance exhaust uni filter A10 Cam Racing CDI Last edited by bigs; 11-20-2009 at 03:47 PM. |
#5
|
||||
|
||||
thats what im thinkin, ill check it later
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#6
|
||||
|
||||
Likely the reverse cable adjustment HOWEVER...these things are kinda bad about breaking that reverse lever thing that sits on the transmission. In fact, thata was the only problem we ever had with our Carbide. I suspect yours may have crapped out. Get a flashlight and look at the piece that the cables attach to in the back and make sure it isn't cracked.
If it is, the replacement pieces are pretty cheap and are actually made out of metal and shouldn't break. |
#7
|
||||
|
||||
the bracket is not broken. ill adjust the cable tomorrow
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#8
|
||||
|
||||
didnt they make a new dezign for the gear selector??
__________________
MY HELIX -20' maxxis tires -1 1/2in.UNI air filter -gutted exaust -extended lugs -headlights -reflectors -my stickers -adjusted suspension -ground out hubs (to fit on the tires) helix 150 |
#9
|
||||
|
||||
Do you mean the metal bracket that holds the gear selector cables on?
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#10
|
||||
|
||||
the stretched reverse cable was all that it was
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! |
#11
|
||||
|
||||
oh lloll
__________________
MY HELIX -20' maxxis tires -1 1/2in.UNI air filter -gutted exaust -extended lugs -headlights -reflectors -my stickers -adjusted suspension -ground out hubs (to fit on the tires) helix 150 |
|
|