![]() |
![]() |
|
Other tech issues For all other technical issues. Think frame, suspension, steering, brakes, etc |
![]() |
|
Thread Tools |
#1
|
|||
|
|||
![]() ![]()
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
#2
|
||||
|
||||
![]()
pix would help. Sounds like a small ID bearing? Spindle or full axle? if you can crack the bearing apart and get it to jsut the inner race, then you can cut that. usually i always lightly sand the shaft right next to the bearing, blow it out with compressed air then hit it with penetrating lube. it doesn't take much rust, dirt or surface imperfections to hang a bearing up.
|
#3
|
||||
|
||||
![]()
Make sure there's no bolts holding it. I believe there's 3 bolts. . But it should come right off without no special tools.
__________________
2. 150cc carters. 1. Baja reaction 150cc dr2 variators Jerseydevil hp. Pipes unifilters gates belts. Yellow main springs hd. Orange coils. |
#4
|
|||
|
|||
![]()
This bad boy right here. I've tried a slide hammer, three claw puller, bastards stuck on tight. I did a bearing change on my TM 150 and one came right off the other was stuck and required "encouragement". I know these are "supposed" to come right off, but in fact, it's not..
![]()
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
#5
|
||||
|
||||
![]()
make sure there is no allen head set screws in the hub part of it.
|
#6
|
|||
|
|||
![]()
Victory!! My mechanic buddy lent me a snap-on slide hammer with a "clamshell"... It still fought to stay on.. Probably going to order a new housing too, seeing as I beat the crap out of this one..
__________________
2013 Trailmaster XRX 150 Type 86 stroker Taida 4V head with 23/22mm valves, forged 4V piston,Taida 62mm jug,forged Taida 8200 KDU stroker crank, Koso high-flow oil pump, Taida case half w/ oil cooler ports, Setrab oil cooler,TrailTec Vapor, Mikuni VM26-606, aluminum 30mm intake, Uni filter, aluminum stack, Hammerhead racing exhaust, MotoRio adjustable CDI/HO Coil, Iridium plug, Full Dr Pulley CVT kit w/ 16g sliders, JD's Mikuni slide kit 2014 Kandi 90B |
#7
|
||||
|
||||
![]()
See, nothing to it! lol sometimes the fight just makes the victory that much sweeter!
|
![]() |
|
|