BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum

Go Back   BuggyMasters.Com - An On Line Mini Buggy Forum and Go Kart Forum > Technical Discussions > 150cc GY6 and Under Engine Tech

150cc GY6 and Under Engine Tech GY6 and Smaller Technical Discussion Forum

Reply
 
Thread Tools
  #1  
Old 06-06-2015, 08:52 PM
greenmachine greenmachine is offline
Lurker
 

Join Date: Feb 2015
Posts: 5
Default What's the best hill climbing set-up

Hay guys. Got a couple of these gy6 buggies.. Carbide Fox and a Tomberlin 150r Baja. We ride in creeks and bottoms. Trying to upgrade the trans to accommodate for the severe loss of power when climbing. I've ordered a 26mm carb&intake, 2000rpm clutch spring set, clutch with wider pads,9gram rollers and a 39 tooth torque sprocket. Any other suggestions would be greatly appreciated! Thanks
Reply With Quote
  #2  
Old 06-06-2015, 11:06 PM
hhgtsplatinum's Avatar
hhgtsplatinum hhgtsplatinum is offline
Lite Contributor
 

Join Date: Jan 2015
Location: georgia
Posts: 98
Default

a 45t sprocket would be the best for the sprocket, I found a 45t and 42t, I went with the 42 since it matches perfectly with my disk brake. I guess next would be a A12 or A13 cam, I am assuming you already changed the intake and exhaust right?
__________________
Hammerhead GTS150 Platinum
PnP Head, A12 Cam, Uni Filter with aluminum intake tube, Custom Straight through Exhaust, hp coil and ngk plug, 11G sliders, 2000 Contra Spring, 1000 Clutch Springs, ITP tires, winch. 130 main Jet, 38 pilot
Reply With Quote
  #3  
Old 06-07-2015, 08:05 PM
greenmachine greenmachine is offline
Lurker
 

Join Date: Feb 2015
Posts: 5
Default

Thanks. The 39 tooth torque sprocket is the largest I could find.
Reply With Quote
  #4  
Old 06-07-2015, 08:08 PM
greenmachine greenmachine is offline
Lurker
 

Join Date: Feb 2015
Posts: 5
Default

Stock cam is a 04-04. I have a 05-09. Would that increase low end torque?
Reply With Quote
  #5  
Old 06-07-2015, 08:22 PM
JERSEYDEVIL's Avatar
JERSEYDEVIL JERSEYDEVIL is offline
Supporting Vendor
 

Join Date: Feb 2011
Location: port charlotte fl
Posts: 831
Default


i have 39's and 45's in stock if you need one give me a holler.
45t is about 9 5/16" dia so check your clearance.
__________________

"LUCIFER" JOYNER JD400,
CROSSHAMMER 250R,
YERF GX150,
CROSSFIRE MBX150,
BMS 800V-TWIN
'16 RZR 900s ,
'17 ACE 900XC,
'99KX250,
'94 KDX200,
'18 SSR SR170TX

Reply With Quote
  #6  
Old 06-07-2015, 08:56 PM
greenmachine greenmachine is offline
Lurker
 

Join Date: Feb 2015
Posts: 5
Default

I'm wanting it for a yerfdog spider box and a Tomberlin 150r
Reply With Quote
  #7  
Old 06-07-2015, 10:05 PM
hhgtsplatinum's Avatar
hhgtsplatinum hhgtsplatinum is offline
Lite Contributor
 

Join Date: Jan 2015
Location: georgia
Posts: 98
Default

Quote:
Originally Posted by greenmachine View Post
Stock cam is a 04-04. I have a 05-09. Would that increase low end torque?
have no idea what 04-04 or 05-09 mean I usually go by series A9- A14 09 for more speed and towards A14 for more torque...A12 has about 27mm on the intake lift... for the sprocket I got a 42T of ebay just type in "42 Tooth Rear Sprocket (#530), 58mm center hole diameter" there are 35, 39, 42,45 and others just make sure u have a 530 size chain and your center home is 58mm...
__________________
Hammerhead GTS150 Platinum
PnP Head, A12 Cam, Uni Filter with aluminum intake tube, Custom Straight through Exhaust, hp coil and ngk plug, 11G sliders, 2000 Contra Spring, 1000 Clutch Springs, ITP tires, winch. 130 main Jet, 38 pilot
Reply With Quote
  #8  
Old 06-08-2015, 04:39 PM
GX150's Avatar
GX150 GX150 is offline
Heavy Contributor
 

Join Date: Dec 2010
Posts: 645
Default

The Yerf-Dog will not take a sprocket larger than 39t without moving the axle or engine. Even with the 39t sprocket, you will need to grind down an unused boss on the engine case for clearance. I ran the 13t drive sprocket with 39t axle sprocket on mine. The Yerf-Dog already has high ratio gears in the final transmission, so that helps it along too.

I ran the A12 cam with a Hammerhead exhaust and UNI cold air intake. I did not do any cylinder, crank or head work, but that will also yield more grunt.

Ignition upgrades will let it spin freer at high RPM, but did nothing for my low end.

Tires make a big difference. I ran 22X8-10 tires on 10x8 rims up front and 22x11-8 tires on 8x10 rims in the rear. running tall tires up front allows the front to roll over things instead of hang on them. Shorter rims in back allow you to air down more without rim damage which gives you better traction than a tire with less sidewall.
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:48 PM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.