|
|
|
#1
10-02-2010, 08:29 AM
|
||||
|
||||
Camshaft
Here's kinda an update on the project buggy I bought a few months ago. I rebuilt the whole dang engine and I tried to start it, but it has no compression! So... I thought I may not have lined up the camshaft. So my question is how do I line that up? And does anyone else have any idea why it doesn't have any compression?
Thanks y'all
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE! 
|
|
#2
10-02-2010, 09:20 AM
|
||||
|
||||
|
http://www.scootdawg.com/downloads/TopEndInstallGY6.pdf
josh this is how its done
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far
|
|
#3
10-09-2010, 07:56 PM
|
||||
|
||||
|
UGH! I can't get it lined up.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE!
|
|
#4
10-09-2010, 08:53 PM
|
||||
|
||||
|
josh stop take a day off read again on how to set-then do it
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far
|
|
#5
10-10-2010, 07:28 AM
|
|||
|
|||
|
1)Stick a long screw driver in the plug hole
2)Raise the piston by hand till the screw driver is all the way up. 3)put the cam in with the big hole pointing up, line in relation to the top of the head, and small holes side to side 4)Put on the chain It's in time
|
|
#6
10-11-2010, 07:44 PM
|
||||
|
||||
|
Chuck- I've done that about three times. We've found someone at my church that's really good at fine tuning engines. He'll take it Saturday.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE!
|
|
#7
10-11-2010, 08:48 PM
|
||||
|
||||
|
josh its not hard to do look at the video
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far
|
|
#8
10-12-2010, 09:58 PM
|
||||
|
||||
|
Josh, what happens when you try to line it up? Keep with it. You've done great so far and this is experience you will remember all your life. Well worth your effort.
Make sure you adjust your valves correctly. If you don't know how, ask!
|
|
#9
10-13-2010, 12:24 AM
|
||||
|
||||
|
Its easy Josh, bring the piston to top dead center than position the cam so that the large hole points strait forward and the two small holes or hash mark lines are lined up with the top of the head. Don't get too anxious. Some times you have to walk away from it. Many times you will not be right on perfect but it will be very close. Don't give up, prove to yourself that you can do it.If you still have problems give me a call and I'll walk you thru it. 662-301-1563
Tom
|
|
#10
10-14-2010, 07:49 AM
|
||||
|
||||
|
Alright guys. I'll try it one more time. I'll tell y'all the outcome later.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE!
|
|
#12
10-14-2010, 10:14 AM
|
||||
|
||||
|
go ahead its not hard to do-after the first time you will find it easy from now on
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far
|
|
#13
10-14-2010, 01:05 PM
|
||||
|
||||
|
Again, it didn't work. I put the piston at top dead center and lined the cam shaft with the edge of the case, and it didn't work. Again.
__________________
-JoshMy Ride: ASW Carbide Mods: Dr. Pulley Hit Clutch FMF Slip-On Exhaust No Rev. CDI Uni Air Filter 130 Main jet 1500 RPM main clutch spring 11g sliders 75w Halogen Headlights CARBIDE!
|
|
#15
10-14-2010, 09:23 PM
|
||||
|
||||
|
or call john 479-531-1178 after 5pm tom is the expert but i do work on them too.
__________________
olderthan 2008 tomberline punisher 1500 spring 12g sliders 30mm cv pumper carb uni filter no rev cdi polaris xlt snowmobile shocks for front w/550 magnum springs & blaster fronts on rear and another buggy built working on mods gk-13 white spring 17 gram sliders so far Last edited by olderthan; 10-14-2010 at 10:00 PM.
|
 |
|
|
